部署NextCloud AIO + Frp + nginx-proxy-manager内网穿透私有云服务

网络拓扑

假设已有域名为nextcloud.yourhost.com
用户通过域名https访问 -> Nginx -> frps -> frpc -> NextCloud
其中Nginx和frps安装在具有公网IP的服务器上，frpc和NextCloud安装在内网服务器中。

Nginx配置

通过docker安装nginx-proxy-manager

外网服务器中，新建个文件夹，创建docker-compose.yml文件

version: '3'
services:app:image: 'jc21/nginx-proxy-manager:latest'container_name: nginx-proxy-managerrestart: unless-stoppedports:- '80:80'  # http端口- '81:81'  # 管理界面端口- '443:443'  # https端口volumes:- ./data:/data- ./letsencrypt:/etc/letsencrypt

docker compose up -d启动后访问81端口打开nginx-proxy-manager管理界面（防火墙记得打开80, 81, 443）

nginx-proxy-manager配置

按下述文档配置nginx-proxy-manager

https://github.com/nextcloud/all-in-one/blob/main/reverse-proxy.md#nginx-proxy-manager—npm

其中Domain Names填入nextcloud.yourhost.com
由于我使用docker安装nginx-proxy-manager，Forward IP应当填docker中的宿主机IP：127.17.0.1（通过ip addr show docker0查找得到）
Forward Port改为 Frps 的vhostHTTPPort，如10080，与下面一致

Frps配置

下载Frp，到外网服务器中，我下载到/opt/frp/，请根据实际情况修改路径。

配置Frps

/opt/frp//frps.toml

bindPort = 37870
auth.token = xxxxx
vhostHTTPPort = 10080
vhostHTTPSPort = 10443

bindPort 为frp服务器和客户端通信端口，记得打开防火墙。
auth.token 可设置为一个随机字符串，用于通信加密。
vhostHTTPPort和vhostHTTPSPort为http/https服务监听端口，用于给本机的nginx访问。

配置Frps开机启动

/etc/systemd/system/frps.service

[Unit]
Description = frp server
After = network.target syslog.target
Wants = network.target[Service]
Type = simple
ExecStart = /opt/frp/frps -c /opt/frp/frps.toml
Restart=on-failure
RestartSec=5s[Install]
WantedBy = multi-user.target

执行

sudo systemctl enable frps
sudo systemctl start frps

Frpc配置

配置Frpc

下载Frp，到内网服务器中，我下载到/opt/frp/，请根据实际情况修改路径。

/opt/frp/frpc.toml

serverAddr = "yourhost.com"
serverPort = 37870
auth.token = xxxxxincludes = ["./confd/*.toml"]

bindPort 和 auth.token 需要与Frps一致，其他根据实际填写。

/opt/frp/confd/nextcloud.toml

[[proxies]]
name = "nextcloud"
type = "http"
localIP = "127.0.0.1"
localPort = 11000
customDomains = ["nextcloud.yourhost.com"]

配置通过nextcloud.yourhost.com访问外网服务器转发到内网服务器的127.0.0.1:11000，内外网服务器之间以及Frpc和NextCloud之间使用http通信。

这里的localPort 要与下面的APACHE_PORT对应

配置Frpc开机启动

/etc/systemd/system/frpc.service

[Unit]
Description = frp client
After = network.target syslog.target
Wants = network.target[Service]
Type = simple
WorkingDirectory=/opt/frp
ExecStart = /opt/frp/frpc -c /opt/frp/frpc.toml
Restart=on-failure
RestartSec=5s[Install]
WantedBy = multi-user.target

执行

sudo systemctl enable frps
sudo systemctl start frps

Nextcloud AIO配置

内网服务器中新建个文件夹，创建docker-compose.yml文件：

version: '3.8'services:nextcloud-aio-mastercontainer:image: ghcr.io/nextcloud-releases/all-in-one:latestcontainer_name: nextcloud-aio-mastercontainerrestart: alwaysports:- "18080:8080"volumes:- aio_mastercontainer:/mnt/docker-aio-config- /var/run/docker.sock:/var/run/docker.sock:roenvironment:- APACHE_PORT=11000- APACHE_IP_BINDING=0.0.0.0- SKIP_DOMAIN_VALIDATION=false- NEXTCLOUD_DATADIR=/newdata/nextcloud- NEXTCLOUD_UPLOAD_LIMIT=128G- NEXTCLOUD_MAX_TIME=36000- NEXTCLOUD_MEMORY_LIMIT=1024M- NEXTCLOUD_ENABLE_DRI_DEVICE=trueinit: truesysctls:- net.core.somaxconn=1024deploy:restart_policy:condition: anyvolumes:aio_mastercontainer:

NEXTCLOUD_DATADIR设置为你的数据储存路径

启动 docker：

docker compose up -d

随后打开localhost:18080执行初始化流程即可完成安装。

常见问题

Imagick插件无法下载

初始化过程中，容器nextcloud-aio-nextcloud可能会卡在Enabling Imagick...

2025-07-04T15:09:58.253331095Z Connection to nextcloud-aio-database (172.20.0.5) 5432 port [tcp/postgresql] succeeded!
2025-07-04T15:09:58.253810507Z + '[' -f /dev-dri-group-was-added ']'
2025-07-04T15:09:58.254285584Z ++ find /dev -maxdepth 1 -mindepth 1 -name dri
2025-07-04T15:09:58.255071763Z + '[' -n /dev/dri ']'
2025-07-04T15:09:58.255453279Z ++ find /dev/dri -maxdepth 1 -mindepth 1 -name renderD128
2025-07-04T15:09:58.256215830Z + '[' -n /dev/dri/renderD128 ']'
2025-07-04T15:09:58.256741487Z ++ stat -c %g /dev/dri/renderD128
2025-07-04T15:09:58.258725601Z + GID=993
2025-07-04T15:09:58.258744684Z + groupadd -g 993 render2
2025-07-04T15:09:58.270615549Z ++ getent group 993
2025-07-04T15:09:58.270649267Z ++ cut -d: -f1
2025-07-04T15:09:58.272696310Z + GROUP=render2
2025-07-04T15:09:58.272728341Z + usermod -aG render2 www-data
2025-07-04T15:09:58.288824588Z + touch /dev-dri-group-was-added
2025-07-04T15:09:58.291171246Z + set +x
2025-07-04T15:09:58.305853077Z Enabling Imagick...

这主要是网络问题，建议等几个小时，如果还是不行，执行下述操作禁用Imagick插件。

禁用 Imagick 插件

在docker-compose.yml的environment:项中添加一行，将PHP插件列表设为空

      - NEXTCLOUD_ADDITIONAL_PHP_EXTENSIONS=

保存后，执行清理，然后重新运行docker compose up -d

清理安装环境

当需要还原到安装前状态时，执行清理

docker compose down --volumes
docker rm -f $(docker ps -aq --filter name=^nextcloud-aio --filter name=^nextcloud_aio)
docker volume rm $(docker volume list -q --filter name=^nextcloud-aio --filter name=^nextcloud_aio)
docker network remove nextcloud-aio
# sudo rm -r /newdata/nextcloud # 路径与上面NEXTCLOUD_DATADIR一致。执行该项会删除NextCloud中的所有用户数据

后记

由于NextCloud必需使用固定域名+SSL，因此使用该方案并不灵活，难以通过多种方式连接NextCloud服务，如在可用时流量走局域网。因此，最后采用了基于Tailscale 的方案。

其中compose.yml配置如下

services:nextcloud-aio-mastercontainer:image: ghcr.io/nextcloud-releases/all-in-one:latestinit: truerestart: alwayscontainer_name: nextcloud-aio-mastercontainer # This line cannot be changed.volumes:- nextcloud_aio_mastercontainer:/mnt/docker-aio-config- /var/run/docker.sock:/var/run/docker.sock:ronetworks:- nextcloud-aioports:- 0.0.0.0:18080:8080environment:APACHE_PORT: 11000APACHE_IP_BINDING: 127.0.0.1SKIP_DOMAIN_VALIDATION: "true"NEXTCLOUD_DATADIR: /newdata/nextcloudNEXTCLOUD_UPLOAD_LIMIT: 128GNEXTCLOUD_MAX_TIME: 36000NEXTCLOUD_MEMORY_LIMIT: 1024MNEXTCLOUD_ENABLE_DRI_DEVICE: "true"caddy:build:context: .dockerfile: Caddy.Dockerfiledepends_on:tailscale:condition: service_healthyrestart: unless-stoppedenvironment:NC_DOMAIN: nextcloud.tailb1a5cf.ts.net # Change this to your domain ending with .ts.net in the format {$TS_HOSTNAME}.{tailnetdomain}volumes:- type: bindsource: ./Caddyfiletarget: /etc/caddy/Caddyfile- type: volumesource: caddy_certstarget: /certs- type: volumesource: caddy_datatarget: /data- type: volumesource: caddy_configtarget: /config- type: volumesource: tailscale_socktarget: /var/run/tailscale/ # Mount the volume for /var/run/tailscale/tailscale.sockread_only: truenetwork_mode: service:tailscaletailscale:image: tailscale/tailscale:v1.82.0environment:TS_HOSTNAME: nextcloud # Enter the hostname for your tailnetTS_AUTH_KEY: tskey-auth-XXXXXXXXXXXX-XXXXXXXXXXXXXX # OAuth client key recommendedTS_EXTRA_ARGS: --advertise-tags=tag:nextcloudinit: truehealthcheck:test: tailscale status --peers=false --json | grep 'Online.*true'start_period: 3sinterval: 1sretries: 3restart: unless-stoppeddevices:- /dev/net/tun:/dev/net/tunvolumes:- type: volumesource: tailscaletarget: /var/lib/tailscale- type: volumesource: tailscale_socktarget: /tmp # Mounting the entire /tmp folder to access tailscale.sockcap_add:- NET_ADMINnetworks:- nextcloud-aio
volumes:nextcloud_aio_mastercontainer:name: nextcloud_aio_mastercontainer # This line cannot be changed.caddy_certs:caddy_config:caddy_data:tailscale:tailscale_sock:
networks:nextcloud-aio:name: nextcloud-aiodriver: bridgeenable_ipv6: falsedriver_opts:com.docker.network.driver.mtu: "1280" # You can set this to 9001 etc. to use jumbo frames, but packets may be dropped.com.docker.network.bridge.host_binding_ipv4: "127.0.0.1" # Harden aiocom.docker.network.bridge.enable_icc: "true"com.docker.network.bridge.default_bridge: "false"com.docker.network.bridge.enable_ip_masquerade: "true"

注意事项

• 需要打开tailscale的HTTPS Certificates
• 获取ts密钥时记得勾选Ephemeral
• 手动迁移/修改数据后输入docker exec -it nextcloud-aio-nextcloud su www-data -c "php /var/www/html/occ files:scan --all"扫描更新